Socomec STATYS (STS)
STATYS (STS)
Socomec STATYS (STS) (ups) ha una mappa Modbus di 56 registri. Function code usati: 3 (holding register). Tipi di dato: bitfield, int16, string. Esempi: STS reference all'indirizzo 256 (FC 3, string); STS serial number all'indirizzo 278 (FC 3, string); CONFIG (0x0120) all'indirizzo 288 (FC 3, string); STATUS 0x0140 all'indirizzo 320 (FC 3, bitfield).
UPSDa documento
Mappa registri Modbus
10 registri
- FC
- 3
- Tipo
- string
- Unità
- —
- Scala
- 1
- Len
- —
- Accesso
- R
- FC
- 3
- Tipo
- string
- Unità
- —
- Scala
- 1
- Len
- —
- Accesso
- R
- FC
- 3
- Tipo
- string
- Unità
- —
- Scala
- 1
- Len
- —
- Accesso
- R
- FC
- 3
- Tipo
- bitfield
- Unità
- —
- Scala
- 1
- Len
- 1
- Accesso
- R
- FC
- 3
- Tipo
- bitfield
- Unità
- —
- Scala
- 1
- Len
- 1
- Accesso
- R
- FC
- 3
- Tipo
- bitfield
- Unità
- —
- Scala
- 1
- Len
- 1
- Accesso
- R
- FC
- 3
- Tipo
- bitfield
- Unità
- —
- Scala
- 1
- Len
- 1
- Accesso
- R
- FC
- 3
- Tipo
- bitfield
- Unità
- —
- Scala
- 1
- Len
- 1
- Accesso
- R
- FC
- 3
- Tipo
- int16
- Unità
- V
- Scala
- 1
- Len
- 1
- Accesso
- R
- FC
- 3
- Tipo
- int16
- Unità
- V
- Scala
- 1
- Len
- 1
- Accesso
- R
| Len | Scala | Endian | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| 256 | STS reference DIM=10 (ASCII). | sts_reference | 3 | string | — | 1 | — | R | — | |
| 278 | STS serial number DIM=10 (ASCII). | sts_serial_number | 3 | string | — | 1 | — | R | — | |
| 288 | CONFIG (0x0120) DIM=16. Nessuna scomposizione per campo fornita dal documento originale. | config_0x0120 | 3 | string | — | 1 | — | R | — | |
| 320 | STATUS 0x0140 bit0=Source 1 OK; bit1=Source 1 critical; bit2=Source 1 out of tolerance; bit3=Source 1 absent; bit4=Power Path 1 OK; bit5=(riservato); bit6=Source 2 OK; bit7=Source 2 critical; bit8=Source 2 out of tolerance; bit9=Source 2 absent; bit10=Power Path 2 OK; bit11=(riservato); bit12=Sources perm. Synchronised; bit13=Sliding Sources; bit14=Sources perm. Not Synchron.; bit15=Sources Instant. Synchron. | status_0x0140 | 3 | bitfield | 1 | 1 | — | R | — | |
| 321 | STATUS 0x0141 bit0=S1 is preferred source; bit1=Load on preferred source; bit2=Load on alternate source; bit3=Load not supplied; bit4=Load on manual by-pass1; bit5=Load on manual by-pass2; bit6=(riservato); bit7=Load on S1; bit8=Load on S2; bit9=(riservato); bit10=Transfer locked ext.; bit11=(riservato); bit12=Output OK; bit13=Output out of tolerance; bit14=Output absent; bit15=(riservato). | status_0x0141 | 3 | bitfield | 1 | 1 | — | R | — | |
| 322 | STATUS 0x0142 bit0=ESD input active; bit1=Q41 closed; bit2=Q42 closed; bit3=SS1 closed; bit4=SS2 closed; bit5=Q30 closed; bit6=Q51 closed; bit7=Q52 closed; bit8-12=(riservato); bit13=Remote controls enabled; bit14=Maintenance alert; bit15=User mode. Nota: la tabella riepilogativa del documento dichiara il blocco STATUS come 4 parole (0x0140-0x0143), ma il dettaglio dei bit copre solo queste 3 parole: la quarta (0x0143) non e' documentata nel manuale e non e' importata. | status_0x0142 | 3 | bitfield | 1 | 1 | — | R | — | |
| 328 | ALARMS 0x0148 bit0=Imminent stop; bit1=Output Isc detection; bit2=Manual By-Pass; bit3=Overload; bit4=SoLink Alarm; bit5=Consecutive Detections; bit6=Switchback impossible; bit7=Transfer impossible; bit8=(riservato); bit9=PowerPath1 deteriorated; bit10=PowerPath1 short circuit; bit11=PowerPath1 in failure; bit12=(riservato); bit13=PowerPath2 deteriorated; bit14=PowerPath2 short circuit; bit15=PowerPath2 in failure. | alarms_0x0148 | 3 | bitfield | 1 | 1 | — | R | — | |
| 329 | ALARMS 0x0149 bit0=Backfeed1 protection open; bit1=Backfeed2 protection open; bit2=Ambient temperature max; bit3-8=(riservato); bit9=Preventive Alarm; bit10=Wrong Configuration; bit11=HMI Alarm; bit12=Electronics alarm; bit13=Custom input alarm; bit14=Maintenance alarm; bit15=General Alarm. | alarms_0x0149 | 3 | bitfield | 1 | 1 | — | R | — | |
| 544 | S1 voltage L1N Nessuna tabella di scala/formato esplicita per questo blocco nel documento originale (a differenza del mapping VU-MAP): riportato a scala 1 (valore grezzo). | s1_voltage_l1n | 3 | int16 | 1 | 1 | V | R | — | |
| 545 | S1 voltage L2N Nessuna tabella di scala/formato esplicita per questo blocco nel documento originale (a differenza del mapping VU-MAP): riportato a scala 1 (valore grezzo). | s1_voltage_l2n | 3 | int16 | 1 | 1 | V | R | — |
Stai vedendo 10 registri su 56.
La mappa completa è riservata agli utenti registrati. La registrazione è gratuita.