socomec MASTERYS
MASTERYS
Importata da documento
| Len | Scala | Endian | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| 4096 | UPS type 26=1/1 SYSTEM, 27=1/1 UPS, 28=1/1 MODULE, 86=3/1 SYSTEM, 87=3/1 UPS, 88=3/1 MODULE, 256=3/3 SYSTEM, 257=3/3 UPS, 258=3/3 MODULE. | ups_type | 3 | uint16 | 1 | 1 | — | R | — | |
| 4097 | Power Potenza nominale UPS, formato kVA*10. | power | 3 | uint16 | 1 | 0.1 | kVA | R | — | |
| 4098 | Module 0=system(concentrator), 1-6=moduli. | module | 3 | uint16 | 1 | 1 | — | R | — | |
| 4099 | Serial number (char 1-2) ASCII, LSB=char1 MSB=char2. | serial_number_char_1_2 | 3 | uint16 | 1 | 1 | — | R | — | |
| 4100 | Serial number (char 3-4) ASCII, LSB=char3 MSB=char4. | serial_number_char_3_4 | 3 | uint16 | 1 | 1 | — | R | — | |
| 4101 | Serial number (char 5-6) ASCII, LSB=char5 MSB=char6. | serial_number_char_5_6 | 3 | uint16 | 1 | 1 | — | R | — | |
| 4102 | Serial number (char 7-8) ASCII, LSB=char7 MSB=char8. | serial_number_char_7_8 | 3 | uint16 | 1 | 1 | — | R | — | |
| 4103 | Serial number (char 9-10) ASCII, LSB=char9 MSB=char10. | serial_number_char_9_10 | 3 | uint16 | 1 | 1 | — | R | — | |
| 4108 | Jbus code Bit0-3=JBUS-Version(0x02=JBUS-P, 0x04=JBUS-PX usato per Masterys), bit4-7=version code, bit8-11=revision code. | jbus_code | 3 | uint16 | 1 | 1 | — | R | — | |
| 4128 | States word 0 (S00-S15) bit0 S00 Input Mains present; bit1 S01 Inverter ON; bit2 S02 Rectifier ON; bit3 S03 Load on Inverter; bit4 S04 Load on Mains/Bypass; bit5 S05 Load on Battery; bit6 S06 Remote command disabled(0=permesso,1=vietato); bit7 S07 ECO/MODE ON; bit8 S08 UPS in Stand-by mode; bit9 S09 Buzzer ON; bit10 S10 Battery Test in progress; bit11 S11 Battery Test programmed; bit12 S12 Battery Test on stand-by; bit13 S13 Battery Test supported; bit14 S14 Battery Test failed; bit15 S15 Battery near end of Back-up. | states_word_0_s00_s15 | 3 | bitfield | 1 | 1 | — | R | — | |
| 4129 | States word 1 (S16-S31) bit0 S16 Battery discharged; bit1 S17 Battery OK; bit7 S23 Inverter synchronised with Mains; bit10 S26 Auxiliary mains OK; bit11 S27 Battery charger ON/OFF; bit12 S28 Auxiliary input frequency out of tolerance; bit13 S29 Scheduling ON/OFF disabled; bit14 S30 UPS on parallel system; bit15 S31 Battery extension present. | states_word_1_s16_s31 | 3 | bitfield | 1 | 1 | — | R | — | |
| 4130 | States word 2 (S32-S47) bit0-5 S32-S37 Modulo 1-6 in parallelo presente; bit6 S38 External state 1; bit7 S39 External state 2; bit8 S40 External state 3; bit9 S41 External state 4; bit10 S42 Commands control table managed(if=1); bit11 S43 Power Share capability available; bit13 S45 Automatic E-Service report; bit14 S46 Operating on generator set. | states_word_2_s32_s47 | 3 | bitfield | 1 | 1 | — | R | — | |
| 4131 | States word 3 (S48-S63) bit0 S48 Maintenance mode active; bit1 S49 First maintenance period. | states_word_3_s48_s63 | 3 | bitfield | 1 | 1 | — | R | — | |
| 4160 | Alarms word 0 (A00-A15) bit0 A00 Alarm present; bit1 A01 Battery Failure/fuse open; bit2 A02 UPS overload; bit4 A04 Digital power supply fault(Vcc); bit6 A06 Auxiliary mains out of tolerance; bit7 A07 Internal over-temperature alarm; bit8 A08 Manual Bypass closed; bit10 A10 Battery charger failure(usare A26); bit13 A13 Precharge voltage out of tolerance; bit14 A14 BOOST output voltage too low; bit15 A15 BOOST output voltage too high. | alarms_word_0_a00_a15 | 3 | bitfield | 1 | 1 | — | R | — | |
| 4161 | Alarms word 1 (A16-A31) bit0 A16 Battery voltage too high; bit2 A18 Overload timeout blocking Inverter; bit4 A20 Configuration data map corrupted; bit5 A21 PLL Fault; bit6 A22 Input mains general alarm; bit7 A23 Rectifier general alarm; bit9 A25 Inverter general alarm; bit10 A26 Battery charger general alarm; bit11 A27 Output voltage over limits; bit14 A30 UPS stopped for overload; bit15 A31 Imminent Stop. | alarms_word_1_a16_a31 | 3 | bitfield | 1 | 1 | — | R | — | |
| 4162 | Alarms word 2 (A32-A47) bit0-5 A32-A37 Modulo 1-6 in parallelo, allarme generale; bit6-9 A38-A41 External Alarm 1-4; bit10 A42 Remote service alarm; bit11 A43 Redundancy Lost; bit12 A44 Maintenance alarm. | alarms_word_2_a32_a47 | 3 | bitfield | 1 | 1 | — | R | — | |
| 4163 | Alarms word 3 (A48-A63) bit1 A49 Battery discharged; bit2 A50 Insufficient resources; bit3 A51 Option board general alarm; bit4 A52 Rectifier fault; bit6 A54 Inverter fault; bit7 A55 Parallel fault; bit8 A56 Generator set general alarm; bit9 A57 Generator set fault; bit10 A58 Emergency STOP; bit11 A59 Battery circuit open; bit12 A60 Fan failure; bit13 A61 Phase detection fault. | alarms_word_3_a48_a63 | 3 | bitfield | 1 | 1 | — | R | — | |
| 4192 | Load phase 1 | load_phase_1 | 3 | uint16 | 1 | 1 | % | R | — | |
| 4193 | Load phase 2 Solo UPS 3/3. | load_phase_2 | 3 | uint16 | 1 | 1 | % | R | — | |
| 4194 | Load phase 3 Solo UPS 3/3. | load_phase_3 | 3 | uint16 | 1 | 1 | % | R | — | |
| 4195 | Total load Somma fase1+2+3, diviso numero fasi. | total_load | 3 | uint16 | 1 | 1 | % | R | — | |
| 4196 | Battery capacity / Remaining Battery Capacity (%) In carica: Battery capacity. In scarica: Remaining Battery Capacity. | battery_capacity_remaining_battery_capacity | 3 | uint16 | 1 | 1 | % | R | — | |
| 4197 | Battery capacity / Remaining Battery Capacity (Ah) In carica: Battery capacity. In scarica: Remaining Battery Capacity. | battery_capacity_remaining_battery_capacity_ah | 3 | uint16 | 1 | 0.1 | Ah | R | — | |
| 4198 | Auxiliary mains star voltage V1 Solo UPS 3/3 o 3/1. | auxiliary_mains_star_voltage_v1 | 3 | uint16 | 1 | 1 | V | R | — | |
| 4199 | Auxiliary mains star voltage V2 Solo UPS 3/3 o 3/1. | auxiliary_mains_star_voltage_v2 | 3 | uint16 | 1 | 1 | V | R | — | |
| 4200 | Auxiliary mains star voltage V3 | auxiliary_mains_star_voltage_v3 | 3 | uint16 | 1 | 1 | V | R | — | |
| 4201 | Output star voltage V1 Solo UPS 3/3. | output_star_voltage_v1 | 3 | uint16 | 1 | 1 | V | R | — | |
| 4202 | Output star voltage V2 Solo UPS 3/3. | output_star_voltage_v2 | 3 | uint16 | 1 | 1 | V | R | — | |
| 4203 | Output star voltage V3 | output_star_voltage_v3 | 3 | uint16 | 1 | 1 | V | R | — | |
| 4204 | Input current phase L1 Solo UPS 3/3 o 3/1. | input_current_phase_l1 | 3 | uint16 | 1 | 1 | A | R | — | |
| 4205 | Input current phase L2 Solo UPS 3/3 o 3/1. | input_current_phase_l2 | 3 | uint16 | 1 | 1 | A | R | — | |
| 4206 | Input current phase L3 | input_current_phase_l3 | 3 | uint16 | 1 | 1 | A | R | — | |
| 4207 | Output current phase L1 Solo UPS 3/3. | output_current_phase_l1 | 3 | uint16 | 1 | 0.1 | A | R | — | |
| 4208 | Output current phase L2 Solo UPS 3/3. | output_current_phase_l2 | 3 | uint16 | 1 | 0.1 | A | R | — | |
| 4209 | Output current phase L3 Solo UPS 3/3. | output_current_phase_l3 | 3 | uint16 | 1 | 0.1 | A | R | — | |
| 4210 | Auxiliary frequency | auxiliary_frequency | 3 | uint16 | 1 | 0.1 | Hz | R | — | |
| 4211 | Output frequency | output_frequency | 3 | uint16 | 1 | 0.1 | Hz | R | — | |
| 4212 | Positive battery voltage | positive_battery_voltage | 3 | uint16 | 1 | 0.1 | V | R | — | |
| 4213 | Negative battery voltage Se presente solo la tensione positiva, la negativa e' fissata a 0. La tensione totale batteria e' la somma dei valori assoluti positivo+negativo. | negative_battery_voltage | 3 | uint16 | 1 | 0.1 | V | R | — | |
| 4214 | Internal UPS temperature | internal_ups_temperature | 3 | uint16 | 1 | 1 | °C | R | — | |
| 4215 | Remaining back-up time | remaining_back_up_time | 3 | uint16 | 1 | 1 | min | R | — | |
| 4216 | Battery current | battery_current | 3 | uint16 | 1 | 0.1 | A | R | — | |
| 4217 | Inverter current phase L1 | inverter_current_phase_l1 | 3 | uint16 | 1 | 0.1 | A | R | — | |
| 4218 | Inverter current phase L2 Solo UPS 3/3. | inverter_current_phase_l2 | 3 | uint16 | 1 | 0.1 | A | R | — | |
| 4219 | Inverter current phase L3 Solo UPS 3/3. | inverter_current_phase_l3 | 3 | uint16 | 1 | 0.1 | A | R | — | |
| 4220 | Positive rectifier voltage | positive_rectifier_voltage | 3 | uint16 | 1 | 1 | V | R | — | |
| 4221 | Negative rectifier voltage | negative_rectifier_voltage | 3 | uint16 | 1 | 1 | V | R | — | |
| 4225 | Input mains star voltage V1 | input_mains_star_voltage_v1 | 3 | uint16 | 1 | 1 | V | R | — | |
| 4226 | Input mains star voltage V2 Solo UPS 3/3 o 3/1. | input_mains_star_voltage_v2 | 3 | uint16 | 1 | 1 | V | R | — | |
| 4227 | Input mains star voltage V3 Solo UPS 3/3 o 3/1. | input_mains_star_voltage_v3 | 3 | uint16 | 1 | 1 | V | R | — | |
| 4228 | Output active power Se disponibile qui, il registro equivalente in kVA e' fissato a 0xFFFF, e viceversa. | output_active_power | 3 | uint16 | 1 | 0.1 | kW | R | — | |
| 4229 | Output power phase 1 | output_power_phase_1 | 3 | uint16 | 1 | 0.1 | kVA | R | — | |
| 4230 | Output power phase 2 Solo UPS 3/3. | output_power_phase_2 | 3 | uint16 | 1 | 0.1 | kVA | R | — | |
| 4231 | Output power phase 3 Solo UPS 3/3. | output_power_phase_3 | 3 | uint16 | 1 | 0.1 | kVA | R | — | |
| 4232 | Input power phase 1 | input_power_phase_1 | 3 | uint16 | 1 | 0.1 | kVA | R | — | |
| 4233 | Input power phase 2 Solo UPS 3/3 o 3/1. | input_power_phase_2 | 3 | uint16 | 1 | 0.1 | kVA | R | — | |
| 4234 | Input power phase 3 Solo UPS 3/3 o 3/1. | input_power_phase_3 | 3 | uint16 | 1 | 0.1 | kVA | R | — | |
| 4235 | Input mains Frequency | input_mains_frequency | 3 | uint16 | 1 | 0.1 | Hz | R | — | |
| 4320 | Nominal star input voltage | nominal_star_input_voltage | 3 | uint16 | 1 | 1 | V | R | — | |
| 4321 | Nominal star output voltage | nominal_star_output_voltage | 3 | uint16 | 1 | 1 | V | R | — | |
| 4322 | Nominal input frequency | nominal_input_frequency | 3 | uint16 | 1 | 1 | Hz | R | — | |
| 4323 | Nominal output frequency | nominal_output_frequency | 3 | uint16 | 1 | 1 | Hz | R | — | |
| 4324 | Firmware version of communication board Es. 1.00. | firmware_version_of_communication_board | 3 | uint16 | 1 | 0.01 | — | R | — | |
| 4325 | Firmware version of internal board 1 | firmware_version_of_internal_board_1 | 3 | uint16 | 1 | 0.01 | — | R | — | |
| 4328 | Total nominal battery capacity Incluse eventuali espansioni batteria. | total_nominal_battery_capacity | 3 | uint16 | 1 | 0.1 | Ah | R | — | |
| 4329 | Total battery number of serial elements | total_battery_number_of_serial_elements | 3 | uint16 | 1 | 1 | — | R | — | |
| 4330 | Number of Power Share Plugs Available | number_of_power_share_plugs_available | 3 | uint16 | 1 | 1 | — | R | — | |
| 4331 | Communication board FW checksum Rappresentazione esadecimale, es. A3F7. | communication_board_fw_checksum | 3 | uint16 | 1 | 1 | — | R | — | |
| 4333 | Working mode bit0=1 autorestart enabled; bit1=1 Converter mode enabled; bit2=1 Gen.set. | working_mode | 3 | bitfield | 1 | 1 | — | R | — | |
| 4334 | Redundancy level 0=Power, 1=N+1, 2=N+2, ecc. | redundancy_level | 3 | uint16 | 1 | 1 | — | R | — | |
| 4335 | Firmware checksum of internal board 1 Rappresentazione esadecimale. | firmware_checksum_of_internal_board_1 | 3 | uint16 | 1 | 1 | — | R | — | |
| 4346 | Counter 6 | counter_6 | 3 | uint16 | 1 | 1 | — | R | — | |
| 4347 | Counter 5 | counter_5 | 3 | uint16 | 1 | 1 | — | R | — | |
| 4348 | Counter 4 | counter_4 | 3 | uint16 | 1 | 1 | — | R | — | |
| 4349 | Counter 3 | counter_3 | 3 | uint16 | 1 | 1 | — | R | — | |
| 4350 | Counter 2 | counter_2 | 3 | uint16 | 1 | 1 | — | R | — | |
| 4351 | Counter 1 | counter_1 | 3 | uint16 | 1 | 1 | — | R | — | |
| 4960 | Date/Time word 1 (Minutes/Seconds) MSB=Minuti(0-59), LSB=Secondi(0-59). 0xFFFF se non disponibile. | date_time_word_1_minutes_seconds | 3 | uint16 | 1 | 1 | — | R/W | — | |
| 4961 | Date/Time word 2 (Day/Hour) MSB=Giorno del mese(1-31), LSB=Ora(0-23). | date_time_word_2_day_hour | 3 | uint16 | 1 | 1 | — | R/W | — | |
| 4962 | Date/Time word 3 (Month/Weekday) MSB=Mese(1-12), LSB=Giorno della settimana(1=lunedì..7=domenica). | date_time_word_3_month_weekday | 3 | uint16 | 1 | 1 | — | R/W | — | |
| 4963 | Date/Time word 4 (Year) LSB=Anno(00-99). | date_time_word_4_year | 3 | uint16 | 1 | 1 | — | R/W | — | |
| 5552 | Command code 0x0000 C00 Reset all commands; 0x0001 C01 Alarms Reset; 0x0002 C02 UPS OFF; 0x0003 C03 ECO MODE enable; 0x0004 C04 ECO MODE disable; 0x0007 C07 Buzzer enable; 0x0008 C08 Buzzer off; 0x000C C12 UPS event history reset; 0x000D C13 Mimic panel LED test; 0x000E C14 Buzzer disable; 0x0010 C16 Immediate Battery Test; valori C15/C17/C18 (power share ON, advanced eco mode, energy saver) riportati nel documento con codifica ambigua/non ancora implementata come comando JBUS, non trascritti singolarmente. | command_code | 6 | uint16 | 1 | 1 | — | W | — | |
| 5568 | Commands control table word 0 (C00-C15) Bit N = 1 se il comando CN-esimo e' abilitato. Gestita solo se lo stato S42 e' impostato a 1. | commands_control_table_word_0_c00_c15 | 3 | bitfield | 1 | 1 | — | R | — | |
| 5569 | Commands control table word 1 (C16-C31) Bit N = 1 se il comando CN-esimo e' abilitato. Gestita solo se lo stato S42 e' impostato a 1. | commands_control_table_word_1_c16_c31 | 3 | bitfield | 1 | 1 | — | R | — |
Leggi questi registri via API
curl https://busbabel.vercel.app/api/devices/socomec/masterys/registers?version=v1